Copper 10Gbps SFP Transceiver HD-10GLC-T RJ45 Port SFP Max 20M
Product Features
- Up to 10Gbps bi-directional data links
- RJ45 Max 20m
- Fully metallic enclosure for low EMI
- Compact RJ-45 Connector assembly
- Hot-pluggable SFP footprint
- Low power dissipation
- Extended case temperature: 0℃ to 70℃
- RoHS compliant and Lead Free
Applications
1. Product Description
The HD-10GLC-T is Copper Small Form pluggable (SFP) transceiver,
which are based on SFP multi-sourcing agreement (MSA). They are
compatible with the 10GBASE-T and 1000BASE-T standards as specified
in IEEE Std 802.3.The 1000BASE-T physical layer IC(PHY) can be
accessed via I2C,allowing access to LIMITED PHY settings and
features
2. Regulatory Compliance
Handar transceivers are Class 1 Laser Products comply with FDA
regulations. Meet Class 1 eye safety requirements of EN 60825 and
the electrical safety requirements of EN 60950.
3. +3.3V Volt Electrical Power Interface
The HD-10GLC-T has an input voltage range of 3.3V +/-5%,The 4 V
maximun voltage is not allowed for continuous operation.
| Parameter | Symbol | Min. | Typ | Max | Units | Notes/Conditions |
| Supply Current | Is | | | 600 | mA | 1.2W max power over full range of voltage and temperature. see
caution note below |
| Power Supply Voltage | Vcc | 3.13 | 3.3 | 3.47 | v | Referenced to GND |
| Maximum Voltage | Vmax | | | 4 | v | |
| Surge Current | Isurge | | | 550 | mA | Hot plug above steady state current, See caution note below |
Caution: Power consumption and surge current are higher than the
specified values in the SFP MSA
Table 1.+3.3 Volt electrical power interface
4. Low-Speed Signals
| Parameter | Symbol | Min. | Max | Units | Notes/Conditions |
| SFP Output LOW | VOL | 0 | 0.5 | V | 4.7k to 10k pull-up to host Vcc, measured at host side of connector |
| SFP Output HIGH | VOH | Host Vcc-0.5 | Host Vcc+0.3 | V | 4.7k to 10k pull-up to host Vcc, measured at host side of connector |
| SFP Input LOW | VIL | 0 | 0.8 | V | 4.7k to 10k pull-up to Vcc, measured at SFP side of connector |
| SFP Input HIGH | VIH | 2 | Vcc+0.3 | V | 4.7k to 10k pull-up to Vcc, measured at SFP side of connector |
Table 2. Low-speed signals, electronic characteristics
5. High-Speed Electrical Interface
ALL high-speed signals are AC-coupled internally
(1)High-speed Electrical Interface Transmission Line-SFP
| Parameter | Symbol | Min. | Typ | Max | Units | Notes/Conditions |
| Line Frequency | fL | 10 | 125 | 1000 | MHZ | 5-level encoding, per IEEE 802.3 |
| Tx Output Impedance | Zout,TX | | 100 | | Ohm | Differential, for all frequencies between 1MHz and 125MHz |
| Rx Input Impedance | Zin,RX | | 100 | | Ohm | Differential, for all frequencies between 1MHz and 125MHz |
Table 3. High-speed electrical interface, transmission line-SFP
(2)High-speed Electrical Interface, Host-SFP
| Parameter | Symbol | Min. | Typ | Max | Units | Notes/Conditions |
| Single ended data input swing | Vinsing | 180 | | 700 | mV | Single ended |
| Single ended data output swing | Voutsing | 350 | | 800 | mV | Single ended |
| Rise/Fall Time | Tr,Tf | | 175 | | psec | 20%-80% |
Tx Input Impedance
| Zin | | 50 | | Ohm | Single ended |
| Rx Output Impedance | Zout | | 50 | | Ohm | Single ended |
Table 4. High-speed electrical interface, host-SFP
6. General Specifications
| Parameter | Symbol | Min. | Typ | Max | Units | Notes/Conditions |
| Data Rate | BR | 10 | | 10000 | Mb/sec | IEEE 802.3 compatible. See Notes 2 through 4 below |
| Tx Output Impedance | L | | | 100 | M | Category 5 UTP.BER<10-12 |
Table 5. General specifications
Note:
1.Clock tolerance is +/- 50 ppm
2.By default, the HD-10GLC-T is a full duplex device in preferred
master mode
3.Automatic crossover detection is enabled. External crossover
cable is not required
4.Multi-BASE-T operation requires the host system to have an SGMII
interface with no clocks, and the module PHY to be configured per
Applications Note AN-2036.With a SERDES that does not support
SGMII, the module will operate at 1000BASE-T only.
7. Environmental Specifications
The HD-GLC-T1/2 has an extended range from 0℃ to +85℃ case
temperature as specified in Table.
| Parameter | Symbol | Min. | Typ | Max | Units | Notes/Conditions |
| Operating Temperature | Top | 0 | | 70 | | Case temperature |
| Storage Temperature | Tsto | 0 | | 70 | | Ambient temperature |
Table 6. Environmental specifications
